ベアリング許容II

Table T1:Normal tolerances for radial bearings


Inner ring
d		△_dmp¹⁾		V_dp Diameter Series			V_dmp	△_Bs		△_B1s		V_Bs	K_ia
				7,8,9	0,1	2,3,4
over mm	incl.	high μm	low	max μm	max	max	max	high μm	low	high μm	low	max μm	max μm



	2.5	0	-8	10	8	6	6	0	-40			12	10
2.5	10	0	-8	10	8	6	6	0	-120	0	-250	15	10
10	18	0	-8	10	8	6	6	0	-120	0	-250	20	10
18	30	0	-10	13	10	8	8	0	-120	0	-250	20	13
30	50	0	-12	15	12	9	9	0	-120	0	-250	20	15
50	80	0	-15	19	19	11	11	0	-150	0	-380	25	20
80	120	0	-20	25	25	15	15	0	-200	0	-380	25	25
120	180	0	-25	31	31	19	19	0	-250	0	-500	30	30
180	250	0	-30	38	38	23	23	0	-300	0	-500	30	40
250	315	0	-35	44	44	26	26	0	-350	0	-500	35	50
315	400	0	-40	50	50	30	30	0	-400	0	-630	40	60
400	500	0	-45	56	56	34	34	0	-450	0	-630	50	65
500	630	0	-50	63	63	38	38	0	-500	0	-800	60	70
630	800	0	-75					0	-750			70	80
800	1000	0	-100					0	-1000			80	90
1000	1250	0	-125					0	-1250			100	100
1250	1600	0	-160					0	-1600			120	120
1600	2000	0	-200					0	-2000			140	140
2000	2500	0	-250					0	-2500			160	160
2500	3150	0	-300					0	-3000			190	180
3150	4000	0	-400					0	-4000			230	200
4000	5000	0	-500					0	-5000			270	230

¹⁾Tolerances for tapered bores,see table T17(taper 1:12) and table T19(taper 1:30)

Table T1:Normal tolerances for radial bearings



d		△_dmp¹⁾		V_dp			V_dmp	△_Bs		△_B1s		V_Bs	K_ia
				Diameter series
				7,8,9	0,1	2,3,4
over	incl.	high	low	max	max	max	max	high	low	high	low	max	max
mm		μm		μm			μm	μm		μm		μm	μm



	2.5	0	-8	10	8	6	6	0	-40			12	10
2.5	10	0	-8	10	8	6	6	0	-120	0	-250	15	10
10	18	0	-8	10	8	6	6	0	-120	0	-250	20	10
18	30	0	-10	13	10	8	8	0	-120	0	-250	20	13
30	50	0	-12	15	12	9	9	0	-120	0	-250	20	15
50	80	0	-15	19	19	11	11	0	-150	0	-380	25	20
80	120	0	-20	25	25	15	15	0	-200	0	-380	25	25
120	180	0	-25	31	31	19	19	0	-250	0	-500	30	30
180	250	0	-30	38	38	23	23	0	-300	0	-500	30	40
250	315	0	-35	44	44	26	26	0	-350	0	-500	35	50
315	400	0	-40	50	50	30	30	0	-400	0	-630	40	60
400	500	0	-45	56	56	34	34	0	-450	0	-630	50	65
500	630	0	-50	63	63	38	38	0	-500	0	-800	60	70
630	800	0	-75					0	-750			70	80
800	1000	0	-100					0	-1000			80	90
1000	1250	0	-125					0	-1250			100	100
1250	1600	0	-160					0	-1600			120	120
1600	2000	0	-200					0	-2000			140	140
2000	2500	0	-250					0	-2500			160	160
2500	3150	0	-300					0	-3000			190	180
3150	4000	0	-400					0	-4000			230	200
4000	5000	0	-500					0	-5000			270	230

¹⁾Applies before bearing is assembled and after removal of internal and/or external snap ring,if used
²⁾Applies only to bearings of Diameter Series 2,3 and 4

Table T2:P6 Class tolerances for radial bearings


Inner ring
d		△_dmp¹⁾		V_dp Diameter Series			V_dmp	△_Bs		△_B1s		V_Bs	K_ia
				7,8,9	0,1	2,3,4
over mm	incl.	high μm	low	max μm	max	max	max	high μm	low	high μm	low	max μm	max μm



	2.5	0	-7	9	7	5	5	0	-40			12	5
2.5	10	0	-7	9	7	5	5	0	-120	0	-250	15	6
10	18	0	-7	9	7	5	5	0	-120	0	-250	20	7
18	30	0	-8	10	8	6	6	0	-120	0	-250	20	8
30	50	0	-10	13	10	8	8	0	-120	0	-250	20	10
50	80	0	-12	15	15	9	9	0	-150	0	-380	25	10
80	120	0	-15	19	19	11	11	0	-200	0	-380	25	13
120	180	0	-18	23	23	14	14	0	-250	0	-500	30	18
180	250	0	-22	28	28	17	17	0	-300	0	-500	30	20
250	315	0	-25	31	31	19	19	0	-350	0	-500	35	25
315	400	0	-30	38	38	23	23	0	-400	0	-630	40	30
400	500	0	-35	44	44	26	26	0	-450	0	-630	45	35
500	630	0	-40	50	50	30	30	0	-500	0	-800	50	40
630	800	0	-50					0	-750			55	45
800	1000	0	-60					0	-1000			60	50
1000	1250	0	-75					0	-1250			70	60
1250	1600	0	-90					0	-1600			70	70
1600	2000	0	-115					0	-2000			80	80
2000	2500	0	-135					0	-2500			120	90

¹⁾ Tolerances for tapered bores (taper 1:12) see table T17

Table T2:P6 Class tolerances for radial bearings


Outer ring
D		△_Dmp		V_Dp¹⁾ Diameter Series Sealed				V_Dmp¹⁾	△_Cs,△_C1s,V_Cs	K_ea
				7,8,9	0,1	2,3,4	beaings²⁾
over mm	incl.	high μm	low	max μm	max	max	max	max		max μm



2.5	18	0	-7	9	7	5	9	5	Values are	8
18	30	0	-8	10	8	6	10	6	indentical to	9
30	50	0	-9	11	9	7	13	7	those for	10
50	80	0	-11	14	11	8	16	8	inner ring	13
80	120	0	-13	16	16	10	20	10	of same	18
120	150	0	-15	19	19	11	25	11	bearing	20
150	180	0	-18	23	23	14	30	14	(△_{Bs△_{B1s△_Bs}})	23
180	250	0	-20	25	25	15		15		25
250	315	0	-25	31	31	19		19		30
315	400	0	-28	35	35	21		21		35
400	500	0	-33	41	41	25		25		40
500	630	0	-38	48	48	29		29		50
630	800	0	-45	56	56	34		34		60
800	1000	0	-60	75	75	45		45		75
1000	1250	0	-75							85
1250	1600	0	-90							100
1600	2000	0	-115							100
2000	2500	0	-135							120

¹⁾Applies before bearing is assembled and after removal of internal and/or external snap ring,if used
²⁾Applies only to bearings of Diameter Series 2,3 and 4

Table T3:P5 Class tolerances for radial bearings


Inner ring
d		△_dmp¹⁾		V_dp Diameter Series		V_dmp	△_Bs		△_B1s		V_Bs	K_ia	S_d	S_ia²⁾
				7,8,9	0,1	2,3,4
over mm	incl.	high μm	low	max μm	max	max	high μm	low	high μm	low	max μm	max μm	max μm	max μm



	2.5	0	-5	5	4	3	0	-40	0	-250	5	4	7	7
2.5	10	0	-5	5	4	3	0	-40	0	-250	5	4	7	7
10	18	0	-5	5	4	3	0	-80	0	-250	5	4	7	7
18	30	0	-6	6	5	3	0	-120	0	-250	5	4	8	8
30	50	0	-8	8	6	4	0	-120	0	-250	5	5	8	8
50	80	0	-9	9	7	5	0	-150	0	-250	6	5	8	8
80	120	0	-10	10	8	5	0	-200	0	-380	7	6	9	9
120	180	0	-13	13	10	7	0	-250	0	-380	8	8	10	10
180	250	0	-15	15	12	8	0	-300	0	-500	10	10	11	13
250	315	0	-18	18	14	9	0	-350	0	-500	13	13	13	15
315	400	0	-23	23	18	12	0	-400	0	-630	15	15	15	20
400	500	0	-28	28	21	14	0	-450	0	-630	18	17	18	23
500	630	0	-35	35	26	18	0	-500	0	-800	20	19	20	25
630	800	0	-45				0	-750			26	22	26	30
800	1000	0	-60				0	-1000			32	26	32	30
1000	1250	0	-75				0	-1250			38	30	38	30
1250	1600	0	-90				0	-1600			45	35	45	30
1600	2000	0	-115				0	-2000			55	40	55	30

¹⁾ Tolerances for tapered bores(taper 1:12) see table T17
²⁾ Applies only to deep groove ball bearings

Table T3:P5 Class tolerances for radial bearings


Outer ring
D		△_Dmp		V_Dp Diameter Series		V_Dmp	△_Cs△_C1s	V_Cs	K_ea	S_D	S_ea²⁾
				7,8,9	0,1,2,3,4
over mm	incl.	high μm	low	max μm	max	max		max μm	max μm	max μm	max μm



2.5	18	0	-5	5	4	3	Values are	5	5	8	8
18	30	0	-6	6	5	3	indentical to	5	6	8	8
30	50	0	-7	7	5	4	those for	5	7	8	8
50	80	0	-9	9	7	5	inner ring	6	8	8	10
80	120	0	-10	10	8	5	of same	8	10	9	11
120	150	0	-11	11	8	6	bearing	8	11	10	13
150	180	0	-13	13	10	7	(△_Bs△_{B1s△_Bs)}	8	13	10	14
180	250	0	-15	15	11	8		10	15	11	15
250	315	0	-18	18	14	9		11	18	13	18
315	400	0	-20	20	15	10		13	20	13	20
400	500	0	-23	23	17	12		15	23	15	23
500	630	0	-28	28	21	14		18	25	18	25
630	800	0	-35	35	26	18		20	30	20	30
800	1000	0	-50	50	29	25		25	35	25	35
1000	1250	0	-63					30	40	30	45
1250	1600	0	-80					35	45	35	55
1600	2000	0	-100					38	55	40	55
2000	2500	0	-125					45	65	50	55

¹⁾ Applies before bearing is assembled and after removal of internal and/or external snap ring, if used
²⁾ Applies only to bearings of Diameter Series 0,1,2,3 and 4

Table T6:SP Class tolerances for radial bearings


Outer ring
D		△_Ds		△_Dmp	V_dp		△_Cs,V_Cs	K_ea	S_D

over mm	incl.	high μm	low	high μm	low	high μm		max μm	max μm



	18	0	-5	3	0	-100	5	3	8
10	30	0	-6	3	0	-100	5	3	8
30	50	0	-8	4	0	-120	5	4	8
50	80	0	-9	5	0	-150	6	4	8
80	120	0	-10	5	0	-200	7	5	9
120	180	0	-13	7	0	-250	8	6	10
180	250	0	-15	8	0	-300	10	8	11
250	315	0	-18	9	0	-350	13	8	13
315	400	0	-23	12	0	-400	15	10	15
400	500	0	-27	14	0	-450	17	10	17
500	630	0	-30	15	0	-500	20	12	20
630	800	0	-40	20	0	-750	30	15	23
800	1000	0	-50	25	0	-1000	33	17	30
1000	1250	0	-65	33	0	-1250	40	20	40

¹⁾ SP tolerances for tapered bores (taper 1:12) see table T18

Table T6:SP Class tolerances for radial bearings


Outer ring
D		△_Ds		△_Dmp	V_dp		△_Cs,V_Cs	K_ea	S_D

over mm	incl.	high μm	low	high μm	low	high μm		max μm	max μm



30	50	0	-7			4	Valuesare	5	8
50	80	0	-9			5	indenticalto	5	8
80	120	0	-10			5	those for	6	9
120	150	0	-11			6	innerring	7	10
150	180	0	-13			7	of same	8	10
180	250	0	-15			8	bearing	10	11
250	315	0	-18			9	(△_Bs,△_Bs）	11	13
315	400	0	-20			10		13	13
400	500	0	-23			12		15	15
500	630	0	-28			14		17	17
630	800			0		18		20	20
800	1000			0		20		23	25
1000	1250			0		25		26	30
1250	1600			0		33		30	35

Table T7:UP Class tolerances for radial bearings


Inner ring
d		△_ds¹⁾		V_dp	△_Bs		V_Bs	K_ia	S_d

over mm	incl.	high μm	low	max μm	high μm	low	max μm	max μm	max μm



	18	0	-4	2	0	-25	1.5	1.5	2
18	30	0	-5	2.5	0	-25	1.5	1.5	3
3	50	0	-6	3	0	-30	2	2	3
50	80	0	-7	3.5	0	-40	3	2	4
80	120	0	-8	4	0	-50	3	3	4
120	180	0	-10	5	0	-60	4	3	5
180	250	0	-12	6	0	-75	5	4	6
250	315	0	-15	8	0	-100	5	4	6
315	400	0	-19	10	0	-100	6	5	7
400	500	0	-23	12	0	-125	7	5	8
500	630	0	-26	13	0	-125	8	6	9

¹⁾ UP tolerances for tapered bores(taper 1:12) see table T18

Table T7:UP Class tolerances for radial bearings


Outer ring
D		△_Ds		△_Dmp	V_dp		△_Cs,V_Cs	K_ea	S_D

over mm	incl.	high μm	low	high μm	low	high μm		max μm	max μm



30	50	0	-5			3	Valuesare	3	2
50	80	0	-6			3	indenticalto	3	2
80	120	0	-7			4	those for	3	3
120	150	0	-8			4	innerring	4	3
150	180	0	-9			5	of same	4	3
180	250	0	-10			5	bearing	5	4
250	315	0	-12			6	(△Bs,△Bs)	6	4
315	400	0	-14			7		7	5
400	500	0	-17			9		8	5
500	630	0	-20			10		9	6
630	800			0	-25	13		11	7

Table T17:Normal、P6、P5 tolerances for tapered bores,taper 1:12



Inner ring
		Tolerance classes Normal,P6					Tolerance class P5
d		△_dmp		V_dp¹⁾	△_d1mp-△_dmp		△_dmp		V_dp¹⁾	△_d1mp-△_dmp

over mm	incl.	high μm	low	max m	high μm	low	high μm	low	max μm	high μm	low



18	30	+21	0	13	+21	0	+13	0	13	+13	0
30	50	+25	0	15	+25	0	+16	0	15	+16	0
50	80	+30	0	19	+30	0	+19	0	19	+19	0
80	120	+35	0	25	+35	0	+22	0	22	+22	0
120	180	+40	0	31	+40	0	+25	0	25	+25	0
180	250	+46	0	38	+46	0	+29	0	29	+29	0
250	315	+52	0	44	+52	0	+32	0	32	+32	0
315	400	+57	0	50	+57	0	+36	0	36	+36	0
400	500	+63	0	56	+63	0	+40	0		+40	0
500	630	+70	0	70	+70	0	+44	0		+44	0
630	800	+80	0		+80	0	+50	0		+50	0
800	1000	+90	0		+90	0	+56	0		+56	0
1000	1250	+105	0		105	0	+66	0		+66	0
1250	1600	+125	0		+125	0	+78	0		+78	0
1600	2000	+150	0		+150	0	+92	0		+92	0

Table T18:SP、UP tolerances for tapered bores,taper 1:12



Inner ring
		Tolerance classe SP					Tolerance class UP
d		△_d2mp		V_dp	△_d3mp-△_d2mp¹⁾		△_d2mp¹⁾		V_dp	△_d3mp-△_d2mp¹⁾

over mm	incl.	high μm	low	max m	high μm	low	high μm	low	max μm	high μm	low



18	30	+10	0	3	+4	0	+6	0	2.5	+2	0
30	50	+12	0	4	+4	0	+7	0	3	+3	0
50	80	+15	0	5	+5	0	+8	0	3.5	+3	0
80	120	+20	0	5	+6	0	+10	0	4	+4	0
120	180	+25	0	7	+8	0	+12	0	5	+4	0
180	250	+30	0	8	+10	0	+14	0	6	+5	0
250	315	+35	0	9	+12	0	+15	0	8	+6	0
315	400	+40	0	12	+12	0	+17	0	10	+6	0
400	500	+45	0	14	+14	0	+19	0	12	+7	0
500	630	+50	0	15	+15	0	+20	0	13	+11	0
630	800	+65	0	20	+19	0	+22	0	17	+13	0
800	1000	+75	0	25	+22	0	+25	0	20	+15	0

¹⁾△_d3mp - △_d2mp = angular deviation over measuring legnth m

Table T19: Tolerances for tapered bores,taper 1:30



Inner ring
		Tolerance classes Normal
d		△_dmp		V_dp¹⁾	△_d1mp-△_dmp

over mm	incl.	high μm	low	max m	high μm	low



	80	+15	0	19	+30	0
80	120	+20	0	22	+35	0
120	180	+25	0	40	+40	0
180	250	+30	0	46	+46	0
250	315	+35	0	52	+52	0
315	400	+40	0	57	+57	0
400	500	+45	0	63	+63	0
500	630	+50	0	70	+70	0
630	800	+75	0		+100	0
800	1000	+100	0		+100	0
1000	1250	+125	0		+115	0
1250	1600	+160	0		+125	0
1600	2000	+200	0		+150	0

¹⁾ Applies in any single radial plane of the bore

Table T10: Tolerances for metric tapered roller bearings - tolerance classes Normal and CL7C



Inner ring,bearing with and ring widths
d		△_dmp		V_dp	V_dmp	△_Bs		K_ia		△_Ts		△_T1s		△_T2s
								Class Normal CL7C
over	incl.	high μm	low	max μm	max μm	high μm	low	max μm	max	high μm	low	high μm	low	high μm	low



10	18	0	-12	12	9	0	-120	15	7	+200	0	+100	0	+100	0
18	30	0	-12	12	9	0	-120	18	8	+200	0	+100	0	+100	0
30	50	0	-12	12	9	0	-120	20	10	+200	0	+100	0	+100	0
50	80	0	-15	15	11	0	-150	25	10	+200	0	+100	0	+100	0
80	120	0	-20	20	15	0	-200	30	13	+200	-200	+100	-100	+100	-100
120	180	0	-25	25	19	0	-250	35		+350	-250	+150	-150	+200	-100
180	250	0	-30	30	23	0	-300	50		+350	-250	+150	-150	+200	-100
250	315	0	-35	35	26	0	-350	60		+350	-250	+150	-150	+200	-100
315	400	0	-40	40	30	0	-400	70		+400	-400	+200	-200	+200	-200
400	500	0	-45	45	34	0	-450	70		+400	-400
500	630	0	-50	50	38	0	-500	85		+500	-500
630	800	0	-75	75	56	0	-750	100		+600	-600
800	1000	0	-100	100	75	0	-1000	120		+750	-750
1000	1250	0	-125			0	-1250	120		+1000	-1000
1250	1600	0	-160			0	-1600	120		+1500	-1500
1600	2000	0	-200			0	-2000	120		+1500	-1500

Table T10: Tolerances for metric tapered roller bearings - tolerance classes Normal and CL7C



Outer ring
D		△_Dmp		V_Dp	V_Dmp	△_Cs		K_ea
								Class Normal CL7C
over	incl.	high μm	low	max μm	max μm	high μm	low	max μm	max



18	30	0	-12	12	9		18	9
30	50	0	-14	14	11	Values are	20	10
50	80	0	-16	16	12	indentical to	25	13
80	120	0	-18	18	14	those for	35	18
120	150	0	-20	20	15	inner ring	40	20
150	180	0	-25	25	19	of same	45	23
180	250	0	-30	30	23	bearing	50
250	315	0	-35	35	26	(△_Bs)	60
315	400	0	-40	40	30		70
400	500	0	-45	45	34		80
500	630	0	-50	50	38		100
630	800	0	-75	75	55		120
800	1000	0	-100	100	75		120
1000	1250	0	-125	125	94		120
1250	1600	0	-160	160	120		120
1600	2000	0	-200				120
2000	2500	0	-250				120

Table T11: CLN Class tolerances for metric tapered roller bearings



Inner ring,bearing with and ring widths
d		△_dmp		V_dp	V_dmp	△_Bs		△_Cs		K_ia	△_Ts		△_T1s		△_T2s

over	incl.	high μm	low	max μm	max μm	high μm	low	high μm	low	Max μm	high μm	low	high μm	low	high μm	low



10	18	0	-12	12	9	0	-50	0	-100	15	+100	0	+50	0	+50	0
18	30	0	-12	12	9	0	-50	0	-100	18	+100	0	+50	0	+50	0
30	50	0	-12	12	9	0	-50	0	-100	20	+100	0	+50	0	+50	0
50	80	0	-15	15	11	0	-50	0	-100	25	+100	0	+50	0	+50	0
80	120	0	-20	20	15	0	-50	0	-100	30	+100	0	+50	0	+100	0
120	180	0	-25	25	19	0	-50	0	-100	35	+150	0	+50	0	+100	0
180	250	0	-30	30	23	0	-50	0	-100	50	+150	0	+50	0	+50	0
250	315	0	-35	35	26	0	-50	0	-100	60	+200	0	+100	0	+100	0
315	400	0	-40	40	30	0	-50	0	-100	70	+200	0	+100	0	+100	0

Table T11: CLN Class tolerances for metric tapered roller bearings



Outer ring
D		△_Dmp		V_Dp	V_dmp	K_ea

over mm	incl.	high μm	low	max μm	max μm	max μm



18	30	0	-12	12	9	18
30	50	0	-14	14	11	20
50	80	0	-16	16	12	25
80	120	0	-18	18	14	35
120	150	0	-20	20	15	40
150	180	0	-25	25	19	45
180	250	0	-30	30	23	50
250	315	0	-35	35	26	60
315	400	0	-40	40	30	70
400	500	0	-45	45	34	80
500	630	0	-50	50	38	100

Table T12: P6 Class tolerances for metric tapered roller bearings



Inner ring
d		△_dmp		V_dp	V_dmp	△_Cs		K_ia

over mm	incl.	high μm	low	max μm	max μm	high μm	low	max μm



80	120	0	-15	11	8	0	-400	13
120	180	0	-18	14	9	0	-500	18
180	250	0	-22	17	11	0	-600	20
250	315	0	-25	19	13	0	-700	25
315	400	0	-30	23	15	0	-800	30
400	500	0	-35	26	18	0	-900	35
500	630	0	-40	30	20	0	-1000	40
630	800	0	-50	50	25	0	-1500	45
800	1000	0	-60	60	30	0	-2000	50

Table T12: P6 Class toler



Outer ring
D		△_Dmp		V_Dp	V_dmp	△_Cs	K_ea

over	incl.	high μm	low	max μm	max μm		max μm



120	150	0	-15	11	8	Valuesare	20
150	180	0	-18	14		indenticalto	23
180	250	0	-20	15		those for	25
250	315	0	-25	19		innerring	30
315	400	0	-28	21		of same	35
400	500	0	-33	25		bearing	40
500	630	0	-38	29		(△_Bs)	50
630	800	0	-45	34			60
800	1000	0	-60	45			75
1000	1250	0	-75	75			75
1250	1600	0	-90	90			75

Tolerances for metric tapered roller bearings

Table T15: Tolerances for inch tapered roller bearings



Inner ring
d		△_ds Tolerance classes
		Normal ,C12		Normal ,C12
over	incl.	high μm	low	high μm	low



	76.2	+13	0	+13	0
76.2	101.6	+13	0	+13	0
101.6	266.7	+13	0	+13	0
266.7	304.8	+13	0	+13	0
304.8	609.6	+25	0	+25	0
609.6	914.4	+38	0	+38	0
914.4	1219.2	+51	0	+51	0
1212.2		+76	0	+76	0

Table T15: Tolerances for inch tapered roller bearings



Inner ring
D		△_Ds Tolerance classes				K_ia,K_ea,S_ia,S_ea Tolerance classes
		Normal,C12		C13,CL0		Normal	CL2	Cl3	C10
over mm	incl.	high μm	low	high μm	low	max μm	max μm	max μm	max μm



	304.8	+25	0	+13	0	51	38	8	4
304.8	609.6	+51	0	+25	0	51	38	18	9
609.6	914.4	+76	0	+38	0	76	51	51	26
914.4	1219.2	+102	0	+51	0	76		76	38
1219.2		+127	0	+76	0	76		76

Table T15: Tolerances for inch tapered roller bearings



Abutment width of single row bearing
d		D		△_Ts Tolerance classes
				Normal		C12		Cl3,C10
over mm	incl.	over mm	incl.	high μm	low	high	low	high μm	low



	101.6			+203	0	+203	0	+203	-203
101.6	266.7			+356	-254	+203	0	+203	-203
266.7	304.8			+356	-254	+203	0	+203	-203
304.8	609.6		508	+381	-381	+381	-381	+203	-203
304.8	609.6	508		+381	-381	+381	-381	+381	-381
609.6				+381	-381			+381	-381

ベアリング許容II

Table T1:Normal tolerances for radial bearings

Table T1:Normal tolerances for radial bearings

Table T2:P6 Class tolerances for radial bearings

Table T2:P6 Class tolerances for radial bearings

Table T3:P5 Class tolerances for radial bearings

Table T3:P5 Class tolerances for radial bearings

Table T6:SP Class tolerances for radial bearings

Table T6:SP Class tolerances for radial bearings

Table T7:UP Class tolerances for radial bearings

Table T7:UP Class tolerances for radial bearings

Table T17:Normal、P6、P5 tolerances for tapered bores,taper 1:12

Table T18:SP、UP tolerances for tapered bores,taper 1:12

Table T19: Tolerances for tapered bores,taper 1:30

Table T10: Tolerances for metric tapered roller bearings - tolerance classes Normal and CL7C

Table T10: Tolerances for metric tapered roller bearings - tolerance classes Normal and CL7C

Table T11: CLN Class tolerances for metric tapered roller bearings

Table T11: CLN Class tolerances for metric tapered roller bearings

Table T12: P6 Class tolerances for metric tapered roller bearings

Table T12: P6 Class toler

Tolerances for metric tapered roller bearings

Table T15: Tolerances for inch tapered roller bearings

Table T15: Tolerances for inch tapered roller bearings

Table T15: Tolerances for inch tapered roller bearings

ＷＤベアリング社